Differences

This shows you the differences between two versions of the page.

--- secstester_getsvidvalue [2020/05/12 19:24]
wikiadmin
+++ secstester_getsvidvalue [2020/05/12 19:29] (current)
wikiadmin
@@ Line 1: / Line 1: @@
 **How to Get an SVID Value from the Tool**
-# Start the SECS Tester
+  - Start the SECS Tester
-# Double-Click on "Set Up Communications to Tool" to open the Communications Setup Dialog
+  - Double-Click on "Set Up Communications to Tool" to open the Communications Setup Dialog
-  * The default tool configuration will be shown. You can change the tool name so that this configuration will be saved as a new tool setup.
+       - The default tool configuration will be shown. You can change the tool name so that this configuration will be saved as a new tool setup.
-  * Enter the HSMS Port (or SECS I Port, a port number < 255)
+       - Enter the HSMS Port (or SECS I Port, a port number < 255)
-  * Enter the Device ID
+       - Enter the Device ID
-  * Enter the new tool name
+       - Enter the new tool name
-  * Save the configuration by pressing the Save button, then the close button
+       - Save the configuration by pressing the Save button, then the close button
-  * # Select the new tool configuration from the combo box. You should see the tool configuration printed out in the text field on the right.
+  - Select the new tool configuration from the combo box. You should see the tool configuration printed out in the text field on the right.
-# Connect to the tool
+   - Connect to the tool
-  *  Press "Connect To Tool" button to send an S1F13 to the tool.
+       - Press "Connect To Tool" button to send an S1F13 to the tool.
-  *  If the communications was successful you will see a response from the tool.
+       -  If the communications was successful you will see a response from the tool.
-  * # Go online-remote with the tool
+  - Go online-remote with the tool
-  *  Be sure the tool is ready to go online with this host and is allowing remote communications.
+       - Be sure the tool is ready to go online with this host and is allowing remote communications.
-  *  Press "Request ONLINE" button to send an S1F17 to the tool.
+       -  Press "Request ONLINE" button to send an S1F17 to the tool.
-  *  If the online request was successful you will see an S1F18 response with a reply other than "1" (which means it cannot go online).
+       - If the online request was successful you will see an S1F18 response with a reply other than "1" (which means it cannot go online).
-  * # Once the tool is ONLINE-REMOTE you can get a list of SVIDs and request the current value of any of them.
+  - Once the tool is ONLINE-REMOTE you can get a list of SVIDs and request the current value of any of them.
-  * Double-Click "Check SVID Values" to launch the SVID Report dialog
+       - Double-Click "Check SVID Values" to launch the SVID Report dialog
-  * Click on the "Get List of SVIDs" button to send an S1F11 to the tool
+       - Click on the "Get List of SVIDs" button to send an S1F11 to the tool
-  * If the tool has SVIDs, these VIDs will show up in the SVID List combo box, alphabetically by SVID name
+       - If the tool has SVIDs, these VIDs will show up in the SVID List combo box, alphabetically by SVID name
-  * Select an SVID and press the "Get Current Value" to send an S1F3 to the tool
+       - Select an SVID and press the "Get Current Value" to send an S1F3 to the tool
-  * The current value will be displayed below the "Get Current Value" button
+       - The current value will be displayed below the "Get Current Value" button